Press the MODE button, till SOUN shows in the led display, confirm one of two modes SOU 1,SOU 2 by the buttons UP, DOWN ,ENTER, then the item will run to the beat of music.
USER MANUAL
LED TRITON
SAFETY INSTRUCTIONS
CAUTION!
Be careful with your operations. With a dangerous voltage you can suffer a dangerous
electric shock when touching the wires!
Keep this device away from rain and moisture!
Unplug mains lead before opening the housing!
For your own safety, please read this user manual carefully before you initial start-up.
Features:
Four operation modes: DMX 512 protocol, auto and master/slave and sound active operating in various modes to form different led effects
DMX-512 connection / connection between fixtures
Occupation of the XLR-connection:
If you are using controllers with this occupation, you can connect the DMX-output of the controller directly with the DMX-input of the first fixture in the DMX-chain. If you wish to connect DMX-controllers with other XLR-outputs, you need to use adapter-cables.
Building a serial DMX-chain:
Connect the DMX-output of the first fixture in the DMX-chain with the DMX-input of the next fixture. Always connect one output with the input of the next fixture until all fixtures are connected.
Caution:At the last fixture, the DMX-cable has to be terminated with a terminator. Solder a 120 resistor between Signal (–) and Signal (+) into a 3-pin XLR-plug and plug it in the DMX-output of the last fixture.
Connection with the mains
Connect the device to the mains with the enclosed power supply cable.
OPERATION
DMX 512 protocol
Addressing
The LED DISPLAY on the rear side of the base allows you to assign the DMX fixture address, which is defined as the first channel from which the item will respond to the controller. If you set, for example, the address to channel 7, the item will use the channel 7 to 14 for control. Please, be sure that you don’t have any overlapping channels in order to control each item correctly and independently from any other fixture on the DMX data link. If two, three or more items are addressed similarly, they will work similarly. At DMX mode you can choose the address from 1 to 512.After you connect the item to the mains, the item starts running. When the item finishes resetting, AOO1 will flash in the led display and then set the desired DMX address by pressing the UP or DOWN buttons.
MODE A:
Six DMX channels:
Channel 1:dimmer,strobe
1-199 Master dimmer from darkness to full brightness
200-247 strobe
248-255 full brightness
Channel 2:color macros
Channel 3:mode selections
Channel 4:running speed adjustments
Channel 5:motor running
0-9 stop
10-120 motor running forward from fast to slow
121-134 stop
135-245 motor running backward from slow to fast
246-255 stop
Channel 6:sound active
0-127 Not occupied
128-255 Sound active
128-256
MODE B:
Twenty-one DMX channels:
Channel 1:dimmer,strobe
1-200 Master dimmer from darkness to full brightness
200-248 strobe
248-255 full brightness
Channel 2: red 1 from darkness to full brightness
Channel 3: green 1 from darkness to full brightness
Channel 4: blue 1 from darkness to full brightness
Channel 5: white 1 from darkness to full brightness
Channel 6: red 2 from darkness to full brightness
Channel 7: green 2 from darkness to full brightness
Channel 8: blue 2 from darkness to full brightness
Channel 9: white 2 from darkness to full brightness
Channel 10: red 3 from darkness to full brightness
Channel 11: green 3 from darkness to full brightness
Channel 12: blue 3 from darkness to full brightness
Channel 13: white 3 from darkness to full brightness
Channel 14: red 4 from darkness to full brightness
Channel 15: green 4 from darkness to full brightness
Channel 16: blue 4 from darkness to full brightness
Channel 17: white 4 from darkness to full brightness
Channel 18:color macros
Channel 19:mode selections
Channel 20:running speed adjustments
Channel 21:motor running
0-10 stop
10-121 motor running forward from fast to slow
121-135 stop
135-246 motor running backward from slow to fast
246-255 stop
2. Sound active
Press the MODE button, till SOUN shows in the led display, confirm one of two modes SOU 1,SOU 2 by the buttons UP, DOWN ,ENTER, then the item will run to the beat of music.
3.auto/ Synchronization & master /slave mode
Press the MODE button, the following functions can be achieved by the button ENTER:
SLND: master/slave running set;
MAST: master running;
SL1: slave running
SL2: slave running
Take one item and set the item at master or at sound active as above, then get other items and press the button MODE, set as above at SL1 or SL2 ,confirm by the button of ENTER, then connect the items to the item at MAST or sound active, disconnect the items from DMX controller, the items will work symtaneously, the item at MAST or sound active works master, the others at SL1 or SL 2 does slave.
LED DISPLAY:
***ADDR: DMX setting
***CHND: 6CH/21CH selections
***SLND: MAST/SL 1/SL 2, master/slave setting
***SOUN: SOU 1/SOU 2 sound active
***SENS 0-100: adjusting the sound sensitivity from 0 to maximum
***SEBY: ON: full on, YES: blackout
***LED: ON/OFF LED DISPLAY
***DISP: DISP/PSID, displaying in the forward direction and reverse direction
***TEST: fixture testing itself
***FHRS: running time records
When one function is set and confirmed as above by the button ENTER, press the MODE button two seconds then you can exit the confirmed function. Whether at auto or sound active, DMX 512 will proceed preferentially.
TECHNICAL SPECIFICATIONS
Power supply: 90-240V AC 50/60Hz
Power consumption: MAX. 60W
Fuse: 250V 1.0A
DMX-control-channels: 6/21CH
DMX-512-connection: 3-pin XLR
Number of LED: 4*four in one high RGBW 10W MCD LEDs, total 40W
Flash-rate: max. 10 Hz
ITEM DIMENSION: 32*32*7CM
ITEM WEIGHT:4KGS
Please note: Every information is subject to change without prior notice.